Illustrated Physics
physics, drawn
Concept

Electromagnetic induction — where it appears

The appearance of an electromotive force around any closed path through which the magnetic flux is changing, whether or not a wire is there. The field it produces is a real electric field with circulation, so it is not derivable from a potential and a voltmeter's reading depends on where its leads run.

Named by 6 essays across one field — each of them below, with the objects they name alongside it.

A loop leaving the field. A rectangular loop of wire 0.3 metres by 0.2 metres moving at 1.5 metres per second out of a region of magnetic field of 0.6 tesla directed into the page, marked with crosses. 0.08 metres of the loop's width is still inside the field. The induced current runs clockwise, and the force on the side that is in the field opposes the motion.

The field that makes the other, and only while it is changing

A magnet sitting next to a coil does nothing at all. Move it and a current flows. The law is not about the field but about its rate of change, and everything electrical since 1831 rests on that distinction.

electromagnetism · Induction A metre of tube, with and without the metal. The magnet's position against time over a 1.00 m drop, integrated from Newton's second law with the eddy-current drag included, and the same fall with the drag switched off. The braked descent takes 2.09 s against 0.45 s in free fall. After a transient of about 50 milliseconds — the mass divided by the drag coefficient, and the only timescale in the problem — the trace is a straight line, which is to say the magnet is falling at a constant 49.0 cm/s. Every joule of the 118 mJ of gravitational energy released has gone into resistive heating of the wall, and none into the magnet's kinetic energy, since that is the same at the bottom as it was a moment after the start.

The magnet that falls slowly

Drop a magnet down a copper pipe and it takes several seconds to fall a metre, drifting rather than falling. Nothing touches it, the copper is not magnetic, and there is no circuit anywhere. The pipe arrives warm.

electromagnetism · Induction A disc that generates 0.785 V with no changing flux anywhere. The force per unit charge on a carrier in a conducting disc of radius 100 mm spinning at 3000 revolutions a minute in an axial field of 0.5 tesla, against how far out the carrier is. Each carrier is moving through the field at ωr, so v × B pushes it radially with a force per unit charge of ωrB — zero at the axle and largest at the rim. The area under the line is the potential difference between the axle and the rim, which is ½BωR² = 0.7854 volts. Nothing in this calculation mentions a loop, a flux or a rate of change, and the flux through the circuit formed by the disc, the contacts and the external wire does not change at all while the machine runs.

The rule that is two laws wearing one coat

The flux rule folds two entirely different pieces of physics into one number, and they agree exactly, which is why nobody notices there are two. A disc spinning in a steady field generates a voltage with no changing flux anywhere, and the folding comes apart.

electromagnetism · Induction How much of μ₀N²A/ℓ a real coil actually has. The inductance of a 140-turn coil of radius 10 mm, divided by the long-solenoid formula μ₀N²A/ℓ, against how long the coil is compared with its diameter. The inductance is computed as a sum of Maxwell's mutual inductances between every pair of turns plus each turn's own, so the long-coil formula appears nowhere in it. At a length equal to the diameter the real coil has 68% of what the formula promises, and at a quarter of the diameter about a third. The reason is that the formula assumes every turn is threaded by the full interior field, and near the ends of a short coil the field has already begun to spread. The ratio is Nagaoka's coefficient, tabulated since 1909, and the computed points agree with the table.

The circuit that fights its own change

Every circuit is threaded by the field its own current makes, so every circuit resists having that current altered. It is the reason a coil takes time to start and the reason breaking one makes a voltage a thousand times the supply's.

electromagnetism · Induction A ring pushed and pulled, and pushed a little more. Over two cycles of the alternating supply, for a ring whose reactance equals its resistance (ωL/R = 1): the flux through the ring (grey), which also sets the radial field that pushes the ring along the core; the voltage induced round the ring (dashed); the current, which lags that voltage by 45° because of the ring's own inductance (blue); and the force along the axis, current times radial field (red). The force pushes the ring away from the coil for part of each half-cycle and pulls it back for the rest; with the lag, the pushes outweigh the pulls, and the average (dotted) is 0.250 of the peak flux–current product. With no lag the pushes and pulls would cancel exactly. The ring jumps because its current is late.

The ring that jumps because its current is late

Slip an aluminium ring over the iron core of a coil, switch on the alternating current, and the ring leaps off the top. The usual explanation is Lenz's law: the ring's induced current opposes the change, so the ring is repelled. But an alternating field changes both ways every cycle, and an induced current that simply opposed the change would be pushed and pulled equally and stay put. The ring jumps only because its current runs late, held back by its own inductance — which is why a cooled ring jumps far higher and a ring with a saw cut through it does not move.

electromagnetism · Induction The resistance a pan offers the coil. The surface resistance — the square root of πfμρ — of five pan materials against frequency, on logarithmic axes, with the band where induction hobs work, 20 to 100 kHz, shaded. All five rise as the square root of the frequency. At 25 kHz carbon steel offers 9.9·10⁻⁴ Ω and ferritic stainless 0.0024 Ω, while austenitic stainless, which is not magnetic, offers 2.7·10⁻⁴ Ω, aluminium 5.1·10⁻⁵ Ω and copper 4.1·10⁻⁵ Ω. For the same coil current the heating goes as this resistance, so steel heats 19 times as hard as aluminium. Matching steel with aluminium by frequency alone would need 377 times the frequency — 9 MHz, where the hob's own electronics and coil would be the problem.

The pan a better conductor will not heat

An induction hob heats a pan with currents the pan carries itself, driven by a field oscillating twenty-five thousand times a second, and it will heat a cast-iron skillet furiously while an aluminium saucepan, which conducts electricity six times better, barely warms. The better conductor is the worse load. What a pan presents to the coil is a surface resistance that goes as the square root of permeability times resistivity, and on that measure iron beats aluminium twenty times over. The same arithmetic explains why kitchen foil on the same hob can catch fire, and why a steel tip heated this way switches itself off at a fixed temperature.

electromagnetism · Induction

Named alongside it

The objects these essays reach for when they reach for this one.

Lenz's lawEmfMagnetic fluxEddy currentsEnergy conservationFaraday's lawField linesJoule heatingResistivityCircuitConductivityConservation of energy

All concepts