Illustrated Physics
physics, drawn
Concept

Contact angle — where it appears

The angle a liquid's edge makes with the solid it rests on, set by the three interfacial tensions meeting at the line rather than by the liquid alone. It decides whether a liquid climbs a tube or is depressed in it, and it takes different values depending on whether the edge last advanced or retreated.

Named by 6 essays across one field — each of them below, with the objects they name alongside it.

Four tubes, four heights. Water in tubes of radius 0.2, 0.4, 0.8, 1.6 mm, with each meniscus drawn as the spherical cap a 20° contact angle forces and each height computed from it. The narrowest rises 70 mm and the widest 9 mm — in inverse proportion to the radius, with nothing about the glass or the volume of water entering it.

How high water will climb

Water rises up a narrow tube against gravity, and the narrower the tube the higher it goes. The height is set by a curved surface pulling on a circumference while gravity pulls on an area, and the two scale differently — which is the whole of it.

fluids · Capillarity One volume of liquid, several solids. 4 drops of the same 5 µL of liquid, on 4 solids it meets at 20°, 60°, 90°, 140°. Each is the spherical cap that volume and that angle force, so the footprint radius is computed rather than chosen: 20° gives 2.61 mm, 60° gives 1.71 mm, 90° gives 1.34 mm, 140° gives 0.69 mm. At every contact line the three interfacial tensions are drawn to scale, and only their horizontal components balance — γsv = γsl + γlv cos θ. The vertical pull of the liquid surface is taken up by the solid, which is why the angle belongs to three interfaces at once and to no single liquid: change the solid and nothing about the water has changed.

The angle a liquid makes with what it sits on

Everything capillarity does — climbing, beading, wicking, waterproofing — is the sign and size of one cosine, and that cosine belongs to three interfaces at once rather than to the water. Change the solid and nothing about the water has changed, yet the same five microlitres goes from a footprint 2.61 mm across to one of 0.69 mm.

fluids · Capillarity Where a drying drop loses its liquid. The rate at which liquid leaves the surface of a drying drop, against distance from the centre in units of the drop's radius, for 5 contact angles. The flux is not uniform, and it is not a property of the liquid: it is set by how vapour diffuses away from a lens-shaped object, which is the same boundary-value problem as the field around a charged lens and has the same answer — a power law in the distance from the rim, with an exponent that depends only on the contact angle. at 10° the exponent is 0.471, and the loss has doubled by 87.8 per cent of the way out, at 40° the exponent is 0.357, and the loss has doubled by 92.5 per cent of the way out, at 70° the exponent is 0.182, and the loss has doubled by 98.9 per cent of the way out, at 90° the exponent is 0.000 and the drop dries evenly everywhere, at 120° the exponent is -0.500 and the flux falls toward the rim. Below a right angle the flux diverges at the contact line; at exactly a right angle it is uniform; above it the edge is the slowest-drying part of the drop. Since a pinned edge must be resupplied from the interior, that sign decides which way the liquid inside the drop flows — and therefore whether everything suspended in it ends up in a ring at the rim or in a spot at the centre.

The ring the drop leaves behind

A drop of coffee dries into a ring rather than a disc, and nothing about coffee is responsible. The pattern is produced by a boundary condition — an edge that cannot move — and it survives replacing the coffee with anything else that will stay suspended.

fluids · Surface tension A pore that lifts 100 m has to be 0.1 µm or finer. Capillary rise against pore radius, both logarithmic, for a liquid of surface tension 72.8 mN/m at a contact angle of 20°. The relation is a straight line of slope −1 — halve the pore and double the rise — and the two horizontal marks are the height in question, 100 m, and the 10.3 m that one atmosphere supports. 0.01 µm lifts 1394.7 m; 0.1 µm lifts 139.5 m; 1 µm lifts 13.9 m; 5 µm lifts 2.8 m; 20 µm lifts 69.7 cm; 50 µm lifts 27.9 cm. The conducting vessels of a tree are tens of microns across and lift under a metre; the pores in the membranes between them are tens of nanometres and would lift kilometres. Those are the same expression at two scales, and only one of them is a pipe.

The column that is pulled, not pushed

A capillary fine enough to lift a hundred metres is far too fine to carry any flow, and one wide enough to carry the flow lifts under a metre. Neither is how the water gets up a tree. The column is under tension — an absolute pressure of −0.88 MPa at the top, which a gas cannot have — held together by cohesion and prevented from tearing by pores a few tens of nanometres across.

fluids · Capillarity One line decides whether it climbs for ever. The wetting condition for a corner, drawn as a map. The horizontal axis is the corner's half-angle and the vertical axis the liquid's contact angle with the walls; the diagonal is θ + α = 90°. Below it the meniscus in the corner curves into the liquid, the capillary pressure grows without bound as the corner narrows, and the liquid wicks along it indefinitely. Above it the curvature has the other sign and the liquid stays put. The boundary is tested by evaluating the meniscus a millionth of a degree either side of it at seventeen half-angles, and it wicks on one side and not the other every time. water on clean glass, right-angled corner: α = 45°, θ = 5° — wicks; water on glass, a 20° groove: α = 10°, θ = 40° — wicks; water on plastic, right-angled corner: α = 45°, θ = 75° — does not. A right-angled corner needs a contact angle under 45°, which water on clean glass has and water on most plastics does not.

The corner a liquid never stops climbing

A narrow tube lifts a liquid to a definite height because it has a smallest width. A corner has none, so the capillary suction it can develop is unbounded — and whether the liquid takes advantage is decided by a single inequality between the contact angle and the corner's own angle.

fluids · Surface tension An angle set by a voltage. The contact angle of water on a fluoropolymer coating with a rest angle of 115°, against the voltage across the coating, for coatings 1 and 3 µm thick with a relative permittivity of 1.93. The Lippmann–Young law cos θ = cos θ₀ + ε₀εᵣV²/2dγ makes the cosine rise as the square of the voltage, so the curve is symmetric about zero volts and steepest where the angle is near 90°. For 1 µm the law reaches complete wetting at 110 V; for 3 µm the law reaches complete wetting at 191 V. It does not get there. In most reported experiments the angle stops falling somewhere in the shaded band and then stays put however high the voltage is raised — contact-angle saturation — and why is still argued: charge trapped in the insulator, ionisation of the air at the sharp edge of the drop, and the thermodynamic stability of the contact line have all been proposed and none accounts for every case.

The angle a voltage can set

A contact angle is treated as a fact about three materials — a solid, a liquid and the air — fixed the moment they are chosen. Put a voltage across a micrometre of insulator under a drop and the angle falls as the square of the voltage, with nothing about the materials changed. Drops can be steered across a chip with no pump, and a lens can focus with no moving part. The law that describes it is exact in its model, and real surfaces stop obeying it at an angle nobody has fully explained.

fluids · Capillarity

Named alongside it

The objects these essays reach for when they reach for this one.

Surface tensionCapillarityLaplace pressureWettingCapillary lengthMeniscusScalingSurface energyBoundary conditionsCapacitanceCavitationCurvature

All concepts